Royal Swimming Pools Hot Tubs, Saunas, Games, and More

866-532-8194

Brass Concrete Anchor for Safety Covers
Additional Images

Replacement brass anchor assembly for in-ground swimming pool safety covers and mesh covers. Solid brass screw-type anchors fit in the pool's perimeter decking and are used to anchor the Safety Cover for the off-season.

  • Fits 3/4" Hole
  • Solid Brass Anchor Assembly
  • Used to anchor safety cover during off season
  • Screw type

The size of the anchor insert head is only relevant when using replacing the insert only! If replacing the entire anchor, the insert head size will not matter.

Details

3/4" Anchor Insert Head

  • 3/4" slotted & hex head
  • 1" x 5/8" threaded bolt with 6 threads per 1/2"

5/8" Anchor Insert Head

  • 5/8" slotted & hex head
  • 1-1/8" x 9/16" threaded bolt with 8-9 threads per 3/4"

Important Installation Information:

It is very important to determine and mark the exact location of anchor hole for Installation of Standard Concrete Brass Anchors before installation procedure begin. Always refer to your safety cover installation manual for proper use and placement of the anchors.

Installation

TOOLS REQUIRED FOR INSTALLATION
- Heavy Duty Rotary Hammer Drill
- ¾” Concrete drill bit with long shaft (carbide / diamond tipped)
- Tape measure
- Tamping Pin tool
- Hammer or rubber mallet
- Lubricant – Teflon or silicone spray

Anchor Hole Drilling


Once you have determined and marked the exact locations of Anchor hole, you can drill holes to accept the Anchor Shells. Make sure to keep the drill perpendicular to the deck surface. Measure the drill bit beveled depth. Then add the height of the anchor shell. Mark this measurement onto your drill bit with electrical tape or use drill guide. Drill the hole into the deck NO MORE THAN THE DEPTH of the Brass Anchor Shell taking care not to over-ream the diameter of the hole. If this does happen, simply apply some adhesive to the Brass Anchor Shell before setting it into the hole. Drilling dust can be removed with a vacuum cleaner or carefully blown out.

Due to the nature of poured concrete, some chipping is normal. This chipping can be reduced by 
using a sharp diamond tip drill bit and a high speed rotary hammer drill. Also our WS014 Brass Anchor Collars should be considered as an option for hiding chipped edges of the deck surface near drilled hole and enhancing the beauty of your deck.

When your anchor hole is properly prepared, remove the Brass Anchor insert and the Brass Anchor 
Shell can be lightly tamped into position by inserting the tamping tool into the Brass Anchor Shell 
and temp it into the deck with a hammer or mallet until it is flush with the deck surface. If you don't have a tamping tool we recommend our WS017 anchor tamping pin tool.

A light Teflon or Silicone spray on the tamping tool prior to tamping will facilitate its easy removal 
after insertion of Brass Anchor Shell into the drilled hole. If the tamping tool should become 
jammed into the Brass Anchor Shell, try gently tapping the tool on the lateral sides to loosen it 
while pulling in an upward direction.

Note: To keep smooth operation it is recommended that anchor inserts be removed each 
fall and spring and shells cleaned out to remove any dirt or debris. The Brass Anchor Insert may also be lightly coated with a Silicone or Teflon spray to ensure smooth operation. DO NOT USE OIL OR GREASE!

The size of the anchor insert head is only relevant when using replacing the insert only! If replacing the entire anchor, the insert head size will not matter.

Details

3/4" Anchor Insert Head

  • 3/4" slotted & hex head
  • 1" x 5/8" threaded bolt with 6 threads per 1/2"

5/8" Anchor Insert Head

  • 5/8" slotted & hex head
  • 1-1/8" x 9/16" threaded bolt with 8-9 threads per 3/4"

The size of the anchor insert head is only relevant when using replacing the insert only! If replacing the entire anchor, the insert head size will not matter.

Details

3/4" Anchor Insert Head

  • 3/4" slotted & hex head
  • 1" x 5/8" threaded bolt with 6 threads per 1/2"

5/8" Anchor Insert Head

  • 5/8" slotted & hex head
  • 1-1/8" x 9/16" threaded bolt with 8-9 threads per 3/4"
Ask a question about this product.

WS011

Brass Concrete Anchor for Safety Covers

$8.99
Now Only $4.99

Code: WS011
Usually Ships In 1-2 Business Days
Choose Anchor Insert Size:
Add Decorative Collar:
Brass Concrete Anchor for Safety Covers
$ 4.99 New Available online